iBright™ T8 LED Fluorescent Light
USER GUIDE
Part Numbers:

HFL-8342N-150550-H1
HFL-8342N-150550-H2
HFL-8342N-120550-H1
HFL-8342N-120550-H2
HFL-8276N-120550-H1
HFL-8276N-120550-H2
HFL-8174N-060550-H1
HFL-8174N-060550-H2

 

NOTE:
This user guide is to explain the steps necessary to use the specified and assure peak performance. Its intended use is for reference only, by a fully qualified electrician or technician. This document should never be considered a substitute for any provision of a regulation or state and/or local code.
Please read this entire manual to fully understand and safely use this product.
Specifications are subject to change without notice. Please visit www.atgelectronics.com for most recent user guide versions.

GETTING STARTED
ATG Electronics® iBright™ T8 LED Fluorescent Light (hereinafter referred to as the LED fluorescent light) is enclosing LEDs into the glass tube housing to emit light like the conventional T series fluorescent light. It is general illumination for using in RVs, Buses, Trains, Task Lighting, Store Displays, Warehouse Illumination and Under Cabinets.
This guide contains important information about installing and operating your new iBright™ T8 LED Fluorescent Light safely and accurately.

Included in this Box
ATG Electronics® iBright™ T8 LED Fluorescent Light, 1 PCs
User Guide, 1Set

Unpacking
1) Unpack and carefully examine the product.
2) Report any damage and save all packing materials if any part is damaged during transport.
3) Do not attempt to use this apparatus if it is damaged.

Warnings
1) Risk of electric shock. Ensure that the power supply is off when installing the device.
2) The device must be installed by a qualified electrician or technician in accordance relevant local codes.

Cautions
1) Suggested continuous working time is around 8 hours, never more than 12 hours.
2) Do not attempt to connect the device until you read and understand the installation instructions.
3) Do not use sharp tools near or on the surface of the device.

User Responsibilities
It is the responsibility of the contractor, installer, purchaser, owner, and user to install, maintain, and operate the LED fluorescent light in such a manner as to comply with all state and local laws, ordinances, and regulations.

Note:
The instructions and precautions set forth in this user guide are not necessarily all-inclusive, all conceivable, or relevant to all applications as ATG Electronics cannot anticipate all conceivable or unique situations.

PLANNING THE INSTALLATION
The device installation requires planning to ensure timely, successful installation with minimal complications and down time.

Planning Suggestions
Consult an Electrical Inspector to review all wiring plans.
Create a Layout Plan drawing, per a Lighting Designer's or Architect's recommendation.
Consult ATG Electronics Application Engineering Services as needed.

Installation Steps
1. Retrofit
1) Take away the starter;
2) Remove the ballast and then reconnect the circuit;
3) Drop iBright? T8 into the fluorescent light fixture;
4) Switch on the power to light iBright? T8.
2. New Installation
1) Drop iBright? T8 into the fluorescent light fixture;
2) Switch on the power to light iBright? T8.

Wiring Diagram
1. Retrofit

Before:

After:


2. New Installation


ATG Electronics® iBright™ T8 LED Fluorescent Light Specifications
Input Voltage: 120VAC/240VAC
Color: White
LED Qty: 342LEDs or 276LEDs or 174LEDs
Lumens: 696 lm~1368 lm
Power Consumption: 8W~15W
Beam Angle: 110 degree
Length: 1500mm (4.92 ft) or 1200mm (3.93 ft) or 600mm (1.96 ft)
Work Environment: Indoor use, applicable for dry environment
* Detailed specifications please refer to the product catalog of iBright™ T8 LED Fluorescent Light.

LED SOURCE LIFE
Traditionally, the definition of life for light sources is defined at the point which 50% of the lamps fail under specified conditions. However, all necessary components in a LED lighting system will determine useful life time. According to the industry standard, ATG Electronics uses the concept of useful light output and rates product life time at standard of "less than 50% lumen maintenance of original light output".
LED exhibits very long operational life time, typically 50,000 hours or more. However, like all light source, LED light output can degrades and also undergo gradual shifts in color over time.
LED chips, performed lighting effects and working environmental conditions, such as temperature, humidity, and ventilation will affect LED lumen maintenance. The overall LED Lighting System life time could vary substantially based on usage and environmental condition.
ATG Electronics always adopts brand chips and high quality materials and components to make LED Lighting Systems.

QUALITY WARRANTY
This product is sold pursuant to ATG Electronics Standard Terms and Conditions which can be found at www.atgelectronics.com and which contain important provi-sions, including, among others, Quality Warranty, exclusions and limitations on ATG Electronics liability for damages, and restrictions on the remedies that are available to you.

Close Window