Part Numbers:	HFS-B024R-036400-L1 HFS-B024Y-036400-L1 HFS-B024B-036400-L1 HFS-B024G-036400-L1 HFS-B024N-036400-L1

NOTE:
This user guide is to explain the steps necessary to use the specified and assure peak performance. Its intended use is for reference only, by a fully qualified electrician or technician. This document should never be considered a substitute for any provision of a regulation or state and/or local code.
Please read this entire manual to fully understand and safely use this product.
Specifications are subject to change without notice. Please visit www.atgelectronics.com for most recent user guide versions.

GETTING STARTED
ATG Electronics® iSignage™ B24 LED Flex Strip is a flexible, cuttable and slim device designed especially for signage lighting and replace conventional neon signs.
iSignage™ S24 adopts high intensity LEDs to operate at 12VDC (safe to humans). It can be joined together via 2-pin power cable, and cut at every 3LEDs to fit different spaces. The slim profile, wide beam angle and small color mixing distance (10cm~15cm or 4”~6”) direct the light distribution to the surface of channel letters, and produce even color.
iSignage™ S24 can also be dimmed with specified dimmer (QColor Remote Dimmer). Power Supplies are available in normal and waterproof versions for indoor and outdoor signs. One meter (3.3 feet) 2-pin power cable can be provided for cases there is big space between power supply and channel letters.
iSiange™ S24 can be easily installed onto channel letter bottom with mounting clips which has 3M tape on the base.
iSignage™ S24 has been successfully installed to light up thousands of channel letters worldwide; besides it can also be used for cove lighting.

This guide contains important information about installing and operating your new iSignage™ S24 safely and accurately.

Included in this Box
iSignage™ S24 LED Flex Strip, 20 PCs
User Guide, 1 Set
White Power Connector(s)
Mounting Clip(s)

Additional Items Needed
Power Supply: 12 VDC QDriver™/XDriver™ LED Power Supply
Control System: QColor™ Remote Dimmer (HCD-00001-000000-RD)

Unpacking
1) Unpack and carefully examine the product.
2) Report any damage and save all packing materials if any part is damaged during transport.
3) Do not attempt to use this apparatus if it is damaged.

Warnings
1) Risk of electric shock. Ensure that the power supply is off when wring or soldering the sections of the device.
2) The device and power supply must be installed and operated by a qualified electrician or technician in accordance relevant local codes.

Cautions
1) Suggested continuous working time is around 8 hours, never more than 12 hours.
2) Do not bend the device too strongly.

User Responsibilities
It is the responsibility of the contractor, installer, purchaser, owner, and user to install, maintain, and operate the device in such a manner as to comply with all state and local laws, ordinances, and regulations.

Note:
The instructions and precautions set forth in this user guide are not necessarily all-inclusive, all conceivable, or relevant to all applications as ATG Electronics cannot anticipate all conceivable or unique situations.

PLANNING THE INSTALLATION
The device installation requires planning to ensure timely, successful installation with minimal complications and down time.

Planning Suggestions
Consult an Electrical Inspector to review all wiring plans.
Create a Layout Plan drawing, per a Lighting Designer’s or Architect’s recommendation.
Consult ATG Electronics Application Engineering Services as needed.

Installation Considerations
When creating your installation plan, consider the following:
1) Location of the device
iSignage™ S24 is non-waterproof which is ONLY suitable for dry environment.
2) Minimum bending diameter
NEVER less than 5cm (1.97 inch)
3) Minimum working unit
Minimum working unit is 3LEDs. Please cut at every 3LEDs at cutting marks.
4) Maximum series-wound quantity
25 pcs.

Installation Steps
1) Place and fix iSignage™ S24 to the defined area according to project layout with mounting clips;
2) Connect iSignage™ S24 with power supply through power adaptor board and power connector;
3) Plug power supply into power outlet to light the whole system.

LED SOURCE LIFE
Traditionally, the definition of life for light sources is defined at the point which 50% of the lamps fail under specified conditions. However, all necessary components in a LED lighting system will determine useful life time. According to the industry standard, ATG Electronics uses the concept of useful light output and rates product life time at standard of “less than 50% lumen maintenance of original light output”.
LED exhibits very long operational life time, typically 50,000 hours or more. However, like all light source, LED light output can degrades and also undergo gradual shifts in color over time.
LED chips, performed lighting effects and working environmental conditions, such as temperature, humidity, and ventilation will affect LED lumen maintenance. The overall LED Lighting System life time could vary substantially based on usage and environmental condition.
ATG Electronics always adopts brand chips and high quality materials and components to make LED Lighting Systems.

QUALITY WARRANTY
This product is sold pursuant to ATG Electronics Standard Terms and Conditions which can be found at www.atgelectronics.com and which contain important provi-sions, including, among others, Quality Warranty, exclusions and limitations on ATG Electronics liability for damages, and restrictions on the remedies that are available to you.