| Part Numbers: |
HCD-00300-000000-RL |
 |
NOTE:
This user guide is to explain the steps necessary to use the specified and assure peak performance. Its intended use is for reference only, by a fully qualified electrician or technician. This document should never be considered a substitute for any provision of a regulation or state and/or local code.
Please read this entire manual to fully understand and safely use this product.
Specifications are subject to change without notice. Please visit www.atgelectronics.com for most recent user guide versions.
GETTING STARTED
ATG Electronics® DynColor™ series RGB DMX Controllers are designed specially for manage most RGB LED products of ATG Electronics.
DynColor™ 300-RL (Part Number: HCD-00300-000000-RL) is compatible with Infinity™ K108T and K150T RGB Rope Lights.
Based on high performance microprocessor technology, supporting standard DMX512 protocol, it is available for cross-platform operation on DMX console or DMX simulation software (our DMX Controllers support most DMX consoles and DMX simulation software, A TEST-OPERATION IS HIGHLY RECOMMANDED.) With this enhanced tool, you can manage and design color changing patterns and changing speeds from across platforms.
With over 30 preprogrammed color changing patterns, including gradual changing, screening and jumping. As a powerful color managing controller, it will enable you to choose the desired pattern and according speed to manage the RGB lighting fixtures.
With 0 to 100 dimming grades, you can also control the color and brightness according to your requirements easily, to mix up to 1 million different colors.
The LCD monitor on the controller offers a easy and visible managing method; the mounting bracket will enable the operator to easily fix the controller onto any place.
This guide contains important information about installing and operating your new DynColor™ 300-RL safely and accurately.
Included in this Box
DynColor™ 300-RL RGB DMX Controller, 1 PCs
User Guide, 1 Set
Power Adaptor, 1 Set
Signal Connector(s)
Unpacking
1) Unpack and carefully examine the product.
2) Report any damage and save all packing materials if any part is damaged during transport.
3) Do not attempt to use this apparatus if it is damaged.
Warnings
1) Risk of electric shock. Ensure that the power supply is off when wring or soldering the sections of the device.
2) The controller shall be installed and operated by a qualified electrician or technician in accordance with relevant local codes.
Precautions
1) Please avoid installing the controller in lightening, intense magnetic and high-voltage fields.
2) The controller should be installed indoors. Otherwise, please add rain shielding.
3) Make sure the wires are connected correctly and avoid short cut and burnt out the fuse.
User Responsibilities
It is the responsibility of the contractor, installer, purchaser, owner, and user to install, maintain, and operate the device in such a manner as to comply with all state and local laws, ordinances, and regulations.
Note:
The instructions and precautions set forth in this user guide are not necessarily all-inclusive, all conceivable, or relevant to all applications as ATG Electronics cannot anticipate all conceivable or unique situations.
PLANNING THE INSTALLATION
This controller installation requires planning to ensure timely, successful installation with minimal complications and down time.
Planning Suggestions
Consult an Electrical Inspector to review all wiring plans.
Create a Layout Plan drawing, per a Lighting Designer’s or Architect’s recommendation.
Consult ATG Electronics Application Engineering Services as needed.
Installation Considerations
When creating your installation plan, consider the following:
1) Location of the controller
ATG Electronics recommends that the controller is placed in dry environment.
2) Selection of soldering tools
Ensure that the tool selected is appropriate for the soldering surface.
3) Length of rope light
Rope lights can be cut or connected to adjustable lengths. Standard minimum working length is 2 meter or 6.56 feet (please verify with your sales representative or the technical support team of ATG Electronics).
The rope light shall be cut exactly at the cutting mark.
4) Maximum Driving Quantity
45 meter.
Installation Steps
1) Make sure the switch is keeping off before wiring or installation.
2) Connect rope light to the data wire on the controller.
3) Connect power plug to power connector on the controller, and plug it into the power outlet.
4) Plug the power adaptor into the controller, and plug it into the power outlet.
5) Switch on the controller, choose the desired color pattern, and set changing speed etc.
Wiring Diagram
Function Introduction
1) Physical Specifications
Dimension: L190 x W120 x H50 mm
Weight: 830g
Working Environment: dry environment
Buttons: MODE, SETUP, UP & DOWN
Data Interfaces: DMX512
Front View
Back View
2) Electrical Specifications
Input Voltage: 110VAC/ 220VAC
Working Voltage: 12VDC
Output Load Current: 1A per line, 3 lines
Output Power: 660W (220V), 330W (110V)
Operation Temperature: -10℃~50℃ (14℉~122℉)
3) Function of Buttons
MODE: Select the preferred pre-programmed color pattern.
SETUP: Set the parameters of selected color pattern.
UP: Increase the parameter step by step
DOWN: Decrease the parameter step by step
4) Mode Introduction
5) How to set the DMX controller under DMX512 mode?
Under DMX512 mode, the DMX controller occupies 2 channels/addresses. The first channel/address is for mode selection; the second channel/address is for speed selection.
Please follow the below steps to set up your DMX controller:
① Set DMX controller to DMX512 MODE;
② Set DMX channel/address for the DMX controller: if the DMX channel/address is set to 13, the controller will occupy channel/address 13 & 14; if the DMX channel/address is set to 128, the controller will occupy channel/address 128 & 129;
③ Manage the first channel/address on the DMX console, like 13 or 128, to select the preferred pattern to use;
④ Manage the second channel/address on the DMX console, like 14 or 129, to set the changing speed.
6) How to set the DMX controller under DMX512 DECODER mode?
Under DMX512 DECODER mode, the DMX controller occupies 3 channels/addresses. The first channel/address is for adjusting brightness of red color; the second channel/address is for adjusting brightness of green color; the third channel/address is for adjusting brightness of blue color.
① Set DMX controller to DMX512 DECODER mode;
② Set DMX channel/address for the DMX controller: if the DMX channel/address is set to 13, the controller will occupy channel/address 13, 14 & 15; if the DMX channel/address is set to 128, the controller will occupy channel/address 128, 129 & 130;
③ Manage the first channel/address on the DMX console, like 13 or 128, to adjust the brightness of red color;
④ Manage the second channel/address on the DMX console, like 14 or 129, to adjust the brightness of green color;
⑤ Manage the third channel/address on the DMX console, like 15 or 130, to adjust the brightness of blue color.
QUALITY WARRANTY
This product is sold pursuant to ATG Electronics Standard Terms and Conditions which can be found at www.atgelectronics.com and which contain important provi-sions, including, among others, Quality Warranty, exclusions and limitations on ATG Electronics liability for damages, and restrictions on the remedies that are available to you.
