Part Numbers:

HMZ-Z006T-004400-L1

NOTE:
This user guide is to explain the steps necessary to use the specified and assure peak performance. Its intended use is for reference only, by a fully qualified electrician or technician. This document should never be considered a substitute for any provision of a regulation or state and/or local code.
Please read this entire manual to fully understand and safely use this product.
Specifications are subject to change without notice. Please visit www.atgelectronics.com for most recent user guide versions.

GETTING STARTED
ATG Electronics® oSignage™ WP series LED Modules are designed for signage lighting and decoration, both indoor and outdoor are applicable; they are ideal alternatives to neon or fluorescent tubes. Color is available in red, yellow, blue, green, white and RGB.

oSignage™ WP6T is square shape, with 6LEDs in, and available in RGB colors. DynColor™ 300-FS, QColor™ 310-FS and QColor™ 020-FS are the related controllers available.

oSignage™ WP series LED Modules are 12VDC input; different models of power supplies are available for your choice. (Please visit http://www.atgelectronics.com/lighting/lighting10_20.html for more information.)
oSignage™ WP series LED Modules can be easily installed onto the surface of the channel letters with the 3M double-sided sticking tape on the back. The red-black power cable between each module is 100mm long; they can be cut and powered up at every one piece or re-connected to apply specific length.
oSignage™ WP series LED Modules are IP68 rated, can be submerged into water. When dimming function needed, you can install a QColor™ Remote Dimmer on the main cable.

oSignage™ WP series LED Modules are the ideal products to light up channel letters, signboards, besides, they can be used for under-counter lighting or decoration lighting. They have been successfully used in homes, hotels, restaurants, stores, shops and clubs etc.

Additional Items Needed
Power Supply: 12 VDC QDriver™ /XDriver™ LED Power Supply

Control System:
DynColor™ 300-FS RGB DMX Controller (Part Number: HCD-00300-000000-FS)
or QColor™ 310-FS RGB Mini Controller(Part Number: HCD-00310-000000-FS)
or QColor™ 020-FS RGB Remote Controller(Part Number: HCD-00020-000000-FS)

Unpacking
1) Unpack and carefully examine the product.
2) Report any damage and save all packing materials if any part is damaged during transport.
3) Do not attempt to use this apparatus if it is damaged.

Warnings
1) Risk of electric shock. Ensure that the power supply is off when wring or soldering the sections of the strip.
2) The device shall be installed and operated by a qualified electrician or technician in accordance relevant local codes.

Cautions
1) Suggested continuous working time is around 8 hours, never more than 12 hours.
2) Do not use sharp tools near or on the surface of the device.

User Responsibilities
It is the responsibility of the contractor, installer, purchaser, owner, and user to install, maintain, and operate the device in such a manner as to comply with all state and local laws, ordinances, and regulations.

Note:
The instructions and precautions set forth in this user guide are not necessarily all-inclusive, all conceivable, or relevant to all applications as ATG Electronics cannot anticipate all conceivable or unique situations.

PLANNING THE INSTALLATION
This device installation requires planning to ensure timely, successful installation with minimal complications and down time.

Planning Suggestions
Consult an Electrical Inspector to review all wiring plans.
Create a Layout Plan drawing, per a Lighting Designer’s or Architect’s recommendation.
Consult ATG Electronics Application Engineering Services as needed.

Installation Considerations
When creating your installation plan, consider the following:
1) Location of the device
oSignage™ WP6T is suitable for both indoor and outdoor applications with IP68 degree.
2) Maximum series-wound quantity
60 pcs.

Installation Steps
1) Remove the 3M tape from the back of oSignage™ WP6T RGB LED Module.
2) Place and fix oSignage™ WP6T RGB LED Module to the defined area according to project layout.
3) Connect the controller to oSignage™ WP6T RGB LED Module. Make sure the common wires and data wires (red, green and blue wires) are connected properly.
4) Connect the power supply to the controller.
5) Plug power supply into power outlet to light the whole system.

Wiring Diagram


oSignage™ WP6T LED Modules Specifications
Operation Voltage: 12 VDC
Color: RGB
LED Qty: 6 LEDs
Lumens: 11.44 lm
Power Consumption: 0.72 W
Dimension: L32*W32*H10 mm (L1.26*W1.26*0.39 inch)
Beam Angle: 80°
IP Rating: IP68 (submersible)
* Detailed specifications please refer to the product catalog of oSignage™ WP6 LED Modules.

QUALITY WARRANTY
This product is sold pursuant to ATG Electronics Standard Terms and Conditions which can be found at www.atgelectronics.com and which contain important provi-sions, including, among others, Quality Warranty, exclusions and limitations on ATG Electronics liability for damages, and restrictions on the remedies that are available to you.