| Part Numbers: |
HWW-X018T-058070-H1 HWW-X018T-058070-H2 |
 |
NOTE:
This user guide is to explain the steps necessary to use the specified and assure peak performance. Its intended use is for reference only, by a fully qualified electrician or technician. This document should never be considered a substitute for any provision of a regulation or state and/or local code.
Please read this entire manual to fully understand and safely use this product.
Specifications are subject to change without notice. Please visit www.atgelectronics.com for most recent user guide versions.
GETTING STARTED
ATG Electronics® Smart™ X18LT RGB LED Wall Washer is the linear and weatherproof (IP65) member of the Smart Wall Washer family. From facade structures to landscapes, Smart™ X18LT generates dynamic washing effect.
Smart™ X18LT features compact linear shape built with high power LEDs; and comes with 1 meter power cable and 0.5 meters signal cable (XLR3 connector) to connect every two wall washers.
The mounting/rotating gears ease the installation and enable a wide rotary angle (up to 180¡ã).
Smart™ X18LT comes with two control methods: self-control and DMX control. Under self-control, it will work under the pre-programmed lighting effect; while under DMX control, Smart™ X18LT will be compatible with any DMX512 console, like DynColor™ 500-SL RGB DMX Controller, to meet lighting designers' specific lighting-effect requirements.
With an IP65 rating, Smart™ X18LT is the right solution for outdoor applications to light up mansions, theaters, casinos, gardens, bridges, shopping centers, theme parks and entertainment plazas etc.
Included in this Box
Smart™ X18LT RGB LED Wall Washer, 1PCs
User Guide, 1Set
Additional Items Needed
Control System: DynColor™ 500-SL RGB DMX Controller
Signal Amplifier: Master™ 192-SA Signal Amplifier
Unpacking
1) Unpack and carefully examine the product.
2) Report any damage and save all packing materials if any part is damaged during transport.
3) Do not attempt to use this apparatus if it is damaged.
Warnings
1) Risk of electric shock. Ensure that the power supply is off when wring or soldering the sections of the device.
2) The device shall be installed and operated by a qualified electrician or technician in accordance relevant local codes.
Cautions
1) Suggested continuous working time is around 8 hours, never more than 12 hours.
2) Do not use sharp tools near or on the surface of the device.
User Responsibilities
Note:
The instructions and precautions set forth in this user guide are not necessarily all-inclusive, all conceivable, or relevant to all applications as ATG Electronics cannot anticipate all conceivable or unique situations.
PLANNING THE INSTALLATION
This device installation requires planning to ensure timely, successful installation with minimal complications and down time.
Planning Suggestions
Consult an Electrical Inspector to review all wiring plans.
Create a Layout Plan drawing, per a Lighting Designer¡¯s or Architect¡¯s recommendation.
Consult ATG Electronics Application Engineering Services as needed.
Installation Considerations
When creating your installation plan, consider the following:
1) Location of the device
Smart™ X18LT is suitable for only dry, wet and damp environment.
2) Control System
Smart™ X18LT can be controlled by DynColor™ 500-SL RGB DMX Controller. Synchronous color changing might be considered before installing.
3) Lighting Distance
The maximum lighting distance for Smart™ X18LT is around 10 meter (32.8 feet).
4) Maximum Series-wound Length
100 meter (328 feet). Master™ 192-SA Signal Amplifier is needed between every 100 meter (328 feet) distance.
1) Place Smart™ X18LT at planned location and direct it to architecture surface.
2) Adjust the rotary angle to requested angle.
3) Connect Smart™ X18LT to each other; Signal Amplifiers are needed to connect between every 100 meters or 328 feet.
4) Complete waterproof treatment at every joint of signal connectors. (Please refer to picture below)
5) Connect the DMX Console to the first Smart™ X18LT.
6) Plug the first Smart™ X18LT and DMX console into power outlet to light up the whole system.
Operation Instruction
1) Function of Buttons
2) How to access and set under DMX-Control mode
A. Once the wall washer is connected to DMX console, it will access DMX-Control mode.
B. Press button "A" to select a parameter to set the DMX address.
C. Press button "B" to set the DMX address.
D. Valid DMX address range: 001~512. (You need refer to the user guide of the DMX Console for more operation information.)
E. Each wall washer occupies three DMX channels including red, green and blue. For example, the wall washer at DMX address 001 occupies the channel 1, 2 and 3; the wall washer at DMX address 256 occupies the channel 256, 257 and 258.
3) How to access and set under Self-Control mode
A. Press button "A" four times, it will access Self-Control mode and shows "PXY".
B. Press button "A" once, certain digital LED starts to flash and access corresponding setup (mode).
C. Press button "B" to set the corresponding setup (speed or brightness). The digital LED increase one bit once (values 1~9)
D. Master/Slave Mode:
¢Ù choose one wall washer as the master and set the DMX address as 001
¢Ú choose other wall washers as slaves and set the DMX addresses as any address except 001
¢Û press button "A" of the master wall washer four times, access Self-Control mode
¢Ü change the mode of the master wall washer, and then all slave wall washers will work synchronously
E. Parameter form of "PXY"
|
4) How to exit from selected mode?
After pressing certain button, please wait for around 10 seconds, it will exit from selected mode. The digital LED stops flashing and the wall washer will memorize the selected mode and parameter.
Wiring Diagram
ATG Electronics® Smart™ X18LT RGB LED Wall Washer Specifications
Input Voltage: 120VAC/240VAC
Color: RGB
LED Qty: 18 LEDs
Lumens (single LED): 44 lm (Red), 70 lm (Green), 15 lm (Blue)
Power Consumption: 28W (Max.)
Beam Angle: 15¡ã
Dimension: L580*W130*H82mm (L22.83*W5.12*H3.23 inch)
IP Rating: IP65 (applicable for dry, wet, damp environment)
* Detailed specifications please refer to the product catalog of Smart™ X18LT RGB LED Wall Washer.
LED SOURCE LIFE
Traditionally, the definition of life for light sources is defined at the point which 50% of the lamps fail under specified conditions. However, all necessary components in a LED lighting system will determine useful life time. According to the industry standard, ATG Electronics uses the concept of useful light output and rates product life time at standard of ¡°less than 50% lumen maintenance of original light output¡±.
LED exhibits very long operational life time, typically 50,000 hours or more. However, like all light source, LED light output can degrades and also undergo gradual shifts in color over time.
LED chips, performed lighting effects and working environmental conditions, such as temperature, humidity, and ventilation will affect LED lumen maintenance. The overall LED Lighting System life time could vary substantially based on usage and environmental condition.
ATG Electronics always adopts brand chips and high quality materials and components to make LED Lighting Systems.
QUALITY WARRANTY
This product is sold pursuant to ATG Electronics Standard Terms and Conditions which can be found at www.atgelectronics.com and which contain important provi-sions, including, among others, Quality Warranty, exclusions and limitations on ATG Electronics liability for damages, and restrictions on the remedies that are available to you.
